Navigant forecasts 40% of new vehicles in 2030 will have some form of autonomous driving capability; 75% by 2035
Dassault Systèmes Acquires SIMPACK

Consortium successfully runs silicon carbide multiport DC-DC converter in EV

100714-prodrive-a
Silicon Carbide multiport DC-DC converter fitted to the Tata Vista EV. Click to enlarge.

A consortium led by motorsport and technology company Prodrive has successfully run a silicon carbide-based multiport DC-DC converter in an electric car. The converter controls power flow between multiple energy sources and has been able to achieve efficiency of 98.7%, while increasing power density and reducing the size and weight of the converter when compared to silicon-based systems.

A key aspect of the converter is the use of silicon carbide devices. These operate at a much higher frequency than equivalent silicon components—at 75 kHz in the test vehicles—with a significant reduction in switching losses. This has resulted in a significant reduction in the size of the magnetic components and has enabled the converter to achieve an efficiency of 98.7%, a gravimetric power density of 10.5 kW/kg and a volumetric power density of 20 kW/liter.

The use of silicon carbide power modules could also allow much higher temperature operation than conventional silicon modules. This provides the potential to integrate the power electronics and IC engine cooling systems in hybrid applications.

The DC-DC converter acts as a hub that transfers energy between key components of the vehicle’s high voltage electrical system. It has four ports: two connect to the traction motor and high voltage battery; a third connects to a secondary energy source, which in this test car is a super capacitor bank; and the fourth powers the vehicle’s 12V systems.

The converter is able to match the voltages of these components and transfer energy between them in response to CAN commands from an external supervisory controller.

The test vehicle is a Tata Vista EV demonstrator vehicle, developed by the Tata Motors European Technical Centre in Warwick, which has a 220 V battery and 37 kW traction motor. The vehicle also has two 200 kJ super capacitor banks, which operate at 75-150 V.

In normal driving, the converter boosts the battery voltage to around 400 V to optimize motor performance and can supplement the battery supply with additional energy from the super-cap banks when the driving situation demands it. During re-generation, the converter transfers energy from the motor to the battery or super-capacitor banks as requested by the supervisory controller. Energy can also be transferred directly between the battery and super capacitor ports. The system can be configured to support other energy sources, such as fuel cells or could supply multiple traction motors.

—Mark Willows, Prodrive electrical systems and control specialist

The consortium is now working on a follow up project which increases the converter operating voltage to 750 V, further increases power density and demonstrates operation at increased coolant temperatures.

For this project we have developed a rolling test bed based on a light commercial vehicle chassis, which has a 75 kW traction motor. The energy storage consists of a 320 V Li-ion battery and two super capacitor banks, all of which were built by Prodrive specifically for this project.

—Mark Willows

The consortium of British companies is backed by the Technology Strategy Board and led by Prodrive, working in conjunction with The University of Manchester, Tata Motors European Technical Centre, IST Power Products, Raytheon Systems and SCISYS.

Prodrive has worked on hybrid and electric vehicle programs for more than a decade, starting with a prototype four-wheel drive parallel petrol/electric hybrid built in 2001. Subsequently it has worked on a number of hybrid and EV projects including: motorcycles, commuter vehicles, passenger cars and trucks covering prototype development through to homologation and diverse electrical technologies from HV batteries, super capacitors, fuel cells and high-speed electrical and mechanical flywheels.

Comments

DaveD

@T2,
Interesting. I was not aware of the Tesla plan to cool the battery pack in prep for rapid charging. I would have thought starting it at a set temperature and really cranking up the cooling to KEEP it in a temperature range during charging would have been a better option.
But it certainly makes sense to do SOMETHING with the cooling system to mitigate negative side effects of the car using their supercharger network.
Thanks for the tip as I was not aware of that one at all.

Roger Pham

The H2-FC is also a battery that has 10x the gravimetric energy density of a Tesla"s pack, at 1.5kWh/kg, and can be charged very fast at 3-5 minutes with out any degradation problem due to either cycle life or calendar life. Very durable battery chemiztry that will not even require precious metals, and is already commercially available.

Engineer-Poet

What does the equivalent of a gallon gasoline can cost you when you're filling your leaf blower with H2?

Roger Pham

@EP,
Kobalt batteries for lawn equipment are real expensive, at ~$1,500/kWh. You will need 4-5 packs for swapping. With H2,the container is not so expensive and you can fill up quickly, thus no swapping. In LA, 1kg of H2 sells for $5, but you get 3x the efficiency w/ FC c/w gasoline small engines.

Engineer-Poet

I very much doubt that a 5000 psi (700 bar) H2 tank is going to be remotely as safe to handle as a gasoline can, and I'm sure it will be many times the cost.

The comments to this entry are closed.