Two EVs at Plymouth State University delivered 1 MWh over 6 months with Fermata Energy bidirectional charging platform
U Birmingham study finds DPFs have limited impact on ultrafine particle emissions

SwRI creates linear motor-driven reciprocating hydrogen compressor for FCEV refueling stations

A new hydrogen compressor developed at Southwest Research Institute (SwRI) can improve the efficiency and reliability of hydrogen compression used in the refueling of fuel cell electric vehicles (FCEVs).

The SwRI-developed linear motor-driven reciprocating compressor (LMRC) is designed to compress hydrogen as a fuel source for FCEVs and other hydrogen-powered vehicles. The advanced compression system utilizes a novel concept of driving a permanent magnet piston inside a hermetically-sealed compressor cylinder through electromagnetic windings.


Schematic of LMRC. Broerman et al.

The LMRC is an improvement over conventional reciprocating compressors as it minimizes the mechanical part count, reduces leakage paths, and is easily modularized for simple field installation.


Southwest Research Institute has created an innovative, more efficient hydrogen compressor. The linear motor-driven reciprocating compressor (LMRC) is designed to compress hydrogen as a fuel source for hydrogen-powered cars. Unlike most hydrogen compressors, the LMRC is hermetically sealed and is driven by a linear motor that allows increased compression efficiency. Courtesy of SwRI.

The LMRC was built and designed to compress hydrogen for refueling vehicles with hydrogen fuel cells. To refuel hydrogen vehicles, the gas must be compressed to high pressures first. So, we set out to design a more efficient, leak-proof compressor.

—SwRI Principal Engineer Eugene Broerman, the project’s lead investigator

A key challenge for hydrogen compression is hydrogen’s small particle size, which increases the potential for leaks as the gas flows through equipment.

Because hydrogen particles are so small, there are inherent material compatibility issues when designing a compressor. The particles are so small that they sneak in and alter materials and equipment performance. For instance, we had some early issues with the hydrogen particles causing magnets to fail, so we had to coat the magnets more effectively to prevent that.

—Eugene Broerman

The novel LMRC features an airtight compressor, hermetically sealed using a combination of SwRI-developed solutions. Coatings protect magnets from hydrogen incursion and embrittlement, while improved valve designs minimize leaks. It also utilizes a ceramic piston to minimize heat expansion and lower stress on its seal.

Typical compressors have a piston and crank mechanism that requires them to make the same motion every time, with every revolution of the motor that’s driving it. SwRI’s LMRC is linearly actuated, so we can change the linear motion profile to optimize the compression process.

—Eugene Broerman

To avoid contaminants in the hydrogen gas, most hydrogen compressors require oil-free mechanisms. Unlike most reciprocating compressors, which have motors that move repeatedly in the same motion and require lubrication for maintenance, the LMRC’s linear motor can move the piston in a user-defined motion pattern, is mounted for vertical motion and has a unique dynamic seal design.

As a result, the compressor’s seals and bearings experience less friction, negating the need for traditional lubrication. It can also be used in a range of compression applications to avoid gas leaking into the atmosphere, such as hazardous gas or flare gas recovery applications.

Originally funded by the US Department of Energy and cost-shared by ACI Services, the LMRC has since been supported by internal research funding at SwRI. The LMRC was successfully run for the first time in 2020 and completed continuous operation at design conditions in mid-to-late 2022. Going forward, Broerman plans to modify different aspects of LMRC’s design to increase efficiency and speeds to boost flow rates and to apply the LMRC to other compression applications requiring hermetic sealing.

SwRI has a multidisciplinary team dedicated to hydrogen energy research initiatives to deploy decarbonization technologies across a broad spectrum of industries.


  • Broerman, Eugene Leo, Poerner, Nathan, and Shade, Willard Norman. (2020) “Linear Motor Reciprocating Compressor (LMRC) for Forecourt Hydrogen Compression”. United States. doi: 10.2172/1894346



This is based on the Libertine linear machine design modified for hydrogen application and for pressure containment.
An easier to read reference:

Another interesting system Libertine developed is the LGN120-P1 opposed free piston internal combustion system, developed in conjunction with MAHLE Powertrain that is fuel agnostic.


Libertine references:


Good design, sealed.


I thought we were moving on from mechanical compression to ionic?

The comments to this entry are closed.